GeGeneral terms and conditions

Wall, color, temperature, humidity

Color dyed completely;

Most sticking problems have to make wall that have not dried The paint dries from outside to in, and may look dry but not.

The color should have dried for at least 20 days (in seasons with more moisture more) If you have dark colors for it should be dried for at least 30 days.

If the colors are base and the water count for 60 days)

If the building or the wall is freshly built, count 90 days)

Some ecological paints do not let anything stick to it, they need a special sticker with a stronger glue)

The wall is smooth or almost smooth;

Your wall should be splintered, or smooth or minimal texture If your wall has a strong texture or the adhesive does not touch it and is deactivated

(on a non-smooth wall ask for a sticker with a stronger glue)

The wall is clean and dry;

Even atmospheric pollution or smoke can affect proper adhesion Clean the surface with cloth dampened in lukewarm water at least 48 hours before adhering

(Use a minimum amount of shampoo in the water, preferably a child's if the wall has grease on it)

Clean the surface again with a dry cloth before adhering

Other factors that affect the wall;

Avoid placing the sticker in direct sunlight or near sources of heat Avoid placing it in a place with direct exposure to air conditioning and rooms with humidity

Adhesive should be done at room temperature, the day at low humidity

The temperature of the wall and the adhesive should be about 21 ° (+ - 3 °)

In the summer months, you prefer to stick the stickers in the morning In winter, make sure you have the stickers inside

Avoid placing days with high humidity

Watch out too!

Select its location and then place it

Use papermaking to determine the position of the paste and then stick the stickers Although it rewinds, the many position changes will disable its glue

Push the stickers !!

The adhesive is activated by pressure, so stick the stickers well Do not forget After paste use a soft cloth and push well, especially what ends

The pressure must be vertical (do not rub the surface)

Avoid touching the glue side, especially with sweaty fingers.

Removing the "transfer"

(Refer only to designs that have this transparent or translucent film that helps you place the sticker) After posting, let it go for 1-2 hours before removing this tapeneral terms and conditions

Wall, color, temperature, humidity

Color dyed completely;

Most paste problems have to make a wall that has not dried. Color dries from outside, and may look dry but it is not.

The color should have been dried for at least 20 days (at a higher moisture content). If you have dark colors for it should be dried for at least 30 days.

If the colors are base and the water is 60 or more,

If the building or the wall is freshly constructed, calculate 90%

Some ecological colors do not let anything stick to it, they need a special sticker with a stronger glue)

The wall is smooth or almost smooth;

Your wall should be splintered, smooth or with minimal texture If your wall has a strong texture or the adhesive does not touch it and is deactivated

(on a non-smooth wall ask for a sticker with a stronger glue)

The wall is clean and dry;

Even atmospheric pollution or smoke may affect proper adhesion Clean the surface with cloth dampened in lukewarm water at least 48 hours before adhering

(Use a minimum of water, preferably a child, if the wall is greasy on it)

Clean the surface again with dry cloth before paste it

Other factors that affect the wall;

Avoid placing the sticker in direct sunlight or near heat sources Avoid placing it in a direct exposure to air and humid rooms

Sealing should be done at room temperature, the day with low humidity

The temperature of the wall and the adhesive should be about 21 ° (+ - 3 °)

In the summer, do you prefer to stick to the autumn morning moods Make sure you have the stickers inside

Avoid placing or running high humidity

Watch also!

Select its location and then place it

Use papermaking to determine the paste position and then stick the stickers Although it rewinds, the multiple shifted position will deactivate its glue

Push the stickers !!

It is activated by pressure, so push the sticks well and forget. After paste, use a soft cloth and push it well, especially what is left

The pressure must be vertical (do not rub the surface)

Avoid touching the glue side, especially with a fingers.

Removing the "transfer"

(Refer only to designs that have this transparent or plain film that helps you place the sticker) After putting on, let go for 1-2 hours before removing this tape

Product added to wishlist